Thanks!
Was thinking about one.
All things considered, unless you need a commercialized round, go with the .338-06.
More, and better, bullets are available.
That said, these loads worked well in my Browning A-Bolt .35 Whelen. Use them at your own risk; it's best to reduce these loads 5%-10% to start. All brass was R-P .35 Whelen, and all primers were Fed 210:
H335/52.5
Sierra 225gr Spire Point Boat-tail (1-1.5MOA)
H335/52.0
Sierra 225gr Spire Point Boat-tail sub-MOA ******* consistently the best load in terms of accuracy and performance on buck deer
IMR4064/53.0
Sierra 225gr Spire Point Boat-tail (sub-MOA)
IMR4064/56.0
Barnes 200gr 'X'* (MOA) (must be seated at least .050" off the lands!!!)
George
------------------
Shoot straight, shoot often, but by all means, use enough gun!
[This message has been edited by GeorgeS (edited 08-20-2001).]
Bill the rifle shoots great. I broke it in with Remington factory ammo, 200 grain core-locks which shot really well. The gun did have pretty stout recoil so I took it to an exceptional gunsmith here and he installed a Vais muzzle brake onto it for me. He also reblued and repolished the barrel. The gun is a dream to shoot now and my wife who is small framed can shoot it off the bench comfortably. I could probably just shoot the factory ammo this year but what fun is that
George
P.S. If you think recoil was stout with 200gr. bullets, you should have tried the 250gr. bullets!
------------------
Shoot straight, shoot often, but by all means, use enough gun!
Does this Abolt of yours have an aftermarket bbl, I never saw a factory abolt in 35 whelen?
Thanks
Bill
No, it was the factory barrel; it was an '06 originally. I had it rebored and rechambered by LaBounty.
George
------------------
Shoot straight, shoot often, but by all means, use enough gun!
George
------------------
Shoot straight, shoot often, but by all means, use enough gun!
FWIW, my limited tests have shown the 200 gr. Rem. PSPCL to be a bit "softer" than the 200 gr. Hornady Spire Points.
For whitetails, I think I'd stick with the 225 BT or the 200 gr. Rem. PSPCL. They'll open up well.
My gun has a Shilen #4 contour barrel and Brown Precision stock on a tang safety Ruger 77 action. Not too heavy, not too light, and balances well. So far, no loads have been disappointing in the accuracy dept., but I still haven't found anything that'll shoot 1/2" - yet!
As to recoil, the 250's do in fact produce more recoil than the lighter bullets. The minimum drop at comb and heel of the Brown Precision stock, and perhaps the flex of the synthetic stock, plus a good recoil pad allow me to shoot quite a few rounds before it starts to become less than pleasant. I shot 40 rds. one day, bench testing, and letting the gun recoil smartly due to a very soft grip on it for the tests. At round #37, I started to find the prospect of pulling the trigger something to consider, but no flinches were revealed at the target. With a good, solid hunting grip on it, there'd be much less recoil effect.
I've been able to get 2660 fps. in the Imp. chamber without anything remotely resembling pressure signs. That's right on the heels of the .338 Winchester, AND with a bigger diameter bullet. At a recent shoot, I was able to ring the 400 yd. gong consistently after only one sighter for drop, and this was with factory .35's, not the Imp.'s. I'd left my reloads at home! I didn't expect this. The 400 yd. plate was 16". All rifles are individuals. I just got lucky on this one.
In the Imp. chamber, I've found good results using IMR-4895, VV N-540 & 550, Varget and R-15. Ironically, 4320, the classic Whelen powder, produced miserable results, giving over 120 fps. vel. variation with Nosler 250 Partitions! Don't have a clue why. Groups @ 100 weren't that bad, but there's no way I'd want to hunt with a load producing that kind of variation.
Aren't rifles and loading funny??? If I were starting loading for a Whelen, std. or Imp., I'd probably start with R-15 and Varget.
You say the BT's blew up on a whitetail? How far away, and what's your muzzle velocity? Just curious, was that deer-zilla sized whitetail or what?
I've just about got myself convinced to build a 35 Whelen next, when my 257 Ackley is finished. I was thinking of the BT for a mule deer bullet, and the partition or TBBC for elk and black bear. I DO still want to try those GS bullets, man they sound great! Now you have me wondering...I was planning on standard Whelen chamber, is yours standard or Ackley?
Was thinking Mauser action, Douglas #3 barrel cut to 22 inches, low mount var-x III in say 2-7 or 2-8 small objective scope, strickly a no frills working rifle, mostly for heavy brush and timber. How is your rig decked out?
------------------
I've used it at the "same velocities" you can get in your 35Whe, however mine were shot in a 350RemMag. And used a bunch of them in 358Wins too. But, I've no argument at all with the folks recommending the 225-250gr bullets.
If you decide to try the 200gr Hornady PSP route, rather than avoiding the shoulder, I'd STRONGLY recommend you include "at least" one shoulder (both if possible) to get drop-in-the-tracks performance. If you go just behind the shoulders with this bullet, the Deer will typically run off a short distance, but provide "two" blood trails that Ray Charles could follow.
If you like the "Explosive Preformance" of the Nosler B-Tips typical with the 6mm and 7mms, I used to be able to get that with the 35cal 200gr Sierra RN (PN #2800) at half the cost of the B-Tips. Haven't used it in awhile, and I'm not sure if they "toughened it up" when they did the rest of them or not.
I've not bought any 35cal B-Tips, so I've no experience with them. Sounds like Ralph experienced what I've seen in the smaller caliber B-Tips.
------------------
Good hunting and clean 1-shot kills, Hot Core
[This message has been edited by Hot Core (edited 08-24-2001).]