The Accurate Reloading Forums
9.3x62?
23 September 2010, 04:53
scottfromdallas9.3x62?
I just bought a CZ 550 FS from Idaho Sharpshooter. I have my dies. I bought some RL15. I have 250 Accubonds, 285 PRVI and 285 NPs. Anyone have any recipes for what I have.
23 September 2010, 06:52
BFaucett
Cheers!
-Bob F.
23 September 2010, 07:13
GSSPquote:
Originally posted by BFaucett:
Cheers!
-Bob F.
Yep!
Alan
23 September 2010, 08:09
vapodogBFaucett's data is better than anything I can find.....I got data for RL-15 for my .35 Whelen from Nosler's data and they don't show RL-15 for the 9.3 X 62.....and the one thing that really frustrates me about Alliant is that they don't have a lot of data like Hodgdon does!
Start at 59 grains and see where it goes....That's where my Whelen is with the 250 AB and your 9.3 should be able to do more!
///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
23 September 2010, 16:20
scottfromdallasThanks BOB and Vapo. I started off with 60 on the Accubonds. I'll see how they do.
23 September 2010, 16:28
steve4102
23 September 2010, 16:45
NakihunterI have passed on a fair bit of info to others on this forum & on other sites. I have some bullet test info as well as I was involved a bit in a project a couple of years ago. Send me a PM with your email & I'll email you about 10 to 15MB of info & articles including the above ones.
"When the wind stops....start rowing. When the wind starts, get the sail up quick."
23 September 2010, 18:29
Hot Corequote:
Originally posted by scottfromdallas:
I just bought a CZ 550 FS from Idaho Sharpshooter. ... Anyone have any recipes for what I have.
Huuuummmmmm....., maybe a shovel or a Backhoe.
You going to use it primarily on Truck Springs?
29 September 2010, 16:36
Cliff LyleScott, I'll check on loaddata.com tonight to see if there is some additional information available.
22 October 2010, 07:00
lawndartThe Sako factory ammunition loads are all awesome. Even better; they publish them.
Go to sako.fi
Their loads all feature VV N-140 powder.
Use their specified load for a 250 grain bullet behind Nosler Accubonds.
Use their specified load for 286-grain bullets for the Nosler Partition.
Those loads just flat-ass work!
22 October 2010, 10:05
Gerryquote:
Go to sako.fi
Their loads all feature VV N-140 powder.
Use their specified load for a 250 grain bullet behind Nosler Accubonds.
Use their specified load for 286-grain bullets for the Nosler Partition.
Those loads just flat-ass work!
+1!
Cheers,
Number 10
31 October 2010, 21:47
Fat_AlbertJust do a "find" under 9.3x62 and you will be up to you arm pits in data. The 9.3x62 is very forgiving. It will work with about 8 or 9 different med. burning powders. Have had best luck with Re 15-Vargent-IMR4064-IMR4320- both 4895. The most accurate bullets I have tried in my 550Cz are Speer 270 and Prvi 285 but you shound not use them because they don't cost $1.25 each and are not marked "PREMIUM".
31 October 2010, 23:22
vapodogquote:
Originally posted by Fat_Albert:
Just do a "find" under 9.3x62 and you will be up to you arm pits in data. The 9.3x62 is very forgiving. It will work with about 8 or 9 different med. burning powders. Have had best luck with Re 15-Vargent-IMR4064-IMR4320- both 4895. The most accurate bullets I have tried in my 550Cz are Speer 270 and Prvi 285 but you shound not use them because they don't cost $1.25 each and are not marked "PREMIUM".
I have come to have a lot of respect for Fat_Albert's posts as they are always worth reading.
This one is in line with his other offerings!
///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
31 October 2010, 23:45
Gerryquote:
Speer 270 and Prvi 285 but you shound not use them because they don't cost $1.25 each and are not marked "PREMIUM".
Agree 100% .....
Cheers,
Number 10
01 November 2010, 07:08
scottfromdallasquote:
Originally posted by Gerry:
quote:
Go to sako.fi
Their loads all feature VV N-140 powder.
Use their specified load for a 250 grain bullet behind Nosler Accubonds.
Use their specified load for 286-grain bullets for the Nosler Partition.
Those loads just flat-ass work!
+1!
I have a few hundred of the 286 PRVI bullets. I did try 60gr of R15 with 250 Accubond. It shoots pretty well. I'll chrony them after hunting season and start working on load development for them and the PRVI.
01 November 2010, 07:19
vapodogquote:
I did try 60gr of R15 with 250 Accubond.
I can't think of a better elk load.
///////////////////////////////////////////////////////////////////////////
"Socialism is a philosophy of failure, the creed of ignorance, and the gospel of envy, its inherent virtue is the equal sharing of misery."
Winston Churchill
08 November 2010, 05:51
GSSPScott,
I just got this.....
a few weeks back and I used the above loads from John Barsness' Medium Mediums and BAM!
Alan
08 November 2010, 06:40
mstarlingAm not an accuracy freek ... so I quite load development at 58 gr RL-15 on Norma or Graf cases with 286 gr Partitions. Makes a little less than 1 MOA groups. Right at 2425 fps.
Gone to Africa twice with it and hunted piggies and deer ... works GREAT! Almost always DRT hits.
Mike
--------------
DRSS, Womper's Club, NRA Life Member/Charter Member NRA Golden Eagles ...
Knifemaker,
http://www.mstarling.com 
