THE ACCURATERELOADING.COM GUN CLEANING FORUM

Go
New
Find
Notify
Tools
Reply
  
Ultrasonic Aluminum Test - With Photo's
 Login/Join
 
one of us
posted


I conducted this test in an effort to see actual results of what happens to unprotected Aluminum when subjected to Ultrasonic cleaning. The test sample is a piece of T-6 grade Aluminum I got from work, and applied a 500 finish to, then went over it with Happich Simichrome Polish to achieve as smooth of finish as possible. The above photo shows the finished piece before being subjected to any treatments. It's size is approx. 2 1/2" X 1 1/2" X 1/2" thick.



This was after 9-1/2 minutes in warm water with a small amount of Palmolive Dish Soap. There is not much change except for some very light, hard to see speckling.



This was after 21 minutes exposure to the Ultrasonic cleaner. More profound frosting of the metal has occurred, along with some enhanced speckling. The frosting appears to have taken on the circular pattern of the plastic tray it was resting on with multiple speckles occurring at 9, 12, and 3 O'clock positions around it.



This was after a full 30 minutes of Ultrasonic exposure. Much more profound frosting has occurred, along with deeper speckles. This would no doubt effect the finish of an Aluminium framed pistol if it had any degree of polish on it. While this test wasn't very scientific, I would conclude that it would be risky to expose any Aluminum firearm parts to Ultrasonic cleaning. I wish the photos were better, but you can see the Ultrasonic treatment did in fact effect the finish, which is what I was trying to determine. Bill T.
 
Posts: 1540 | Location: Glendale, Arizona | Registered: 27 December 2003Reply With Quote
one of us
posted Hide Post
A scientific test would require a perfectly clean surface then use distilled or deionized water. Things like the soap or minerals in the water can have a great effect on the aluminum as can the pH of the water..
 
Posts: 7636 | Registered: 10 October 2002Reply With Quote
One of Us
posted Hide Post
One test of the efficency of an ultrasonic cleaner is to see if will make holes in thin aluminum foil. If the cleaner is working it will actually make very small holes in the foil which can be detected by holding the foil up and looking at a bright light.

If you are cleaning a anodized and painted surface the effect is usually less as the paint is softer and less effected by the ultrasonic cleaning.

Remmeber that an ultrasonic leaner works best on hard brittle matterials; the caviation introduced by the cleaning literally blasts holes in the surface material as the bubbles are formed and collapsed like a small shaped charge. This is why an ultrasonic cleaner will clean the brittle material out of the primer pockets but fail to remove any grease of gum left on the case.

The Navy has a good filn on the effect - it may be posted on the web somewhere.
 
Posts: 100 | Location: Alaska | Registered: 27 January 2008Reply With Quote
new member
posted Hide Post
Do you know what the alloy of the test piece is?
 
Posts: 57 | Location: North Central Washington | Registered: 19 June 2003Reply With Quote
one of us
posted Hide Post
quote:
Originally posted by dedseven:
Do you know what the alloy of the test piece is?


T-6. I would have to look up the exact metalurgical content. Bill T.
 
Posts: 1540 | Location: Glendale, Arizona | Registered: 27 December 2003Reply With Quote
one of us
posted Hide Post
T-6 indicates the heat treatment , not the alloy !! A very common alloy and HT is 6061 T-6.
 
Posts: 7636 | Registered: 10 October 2002Reply With Quote
  Powered by Social Strata  
 


Copyright December 1997-2023 Accuratereloading.com


Visit our on-line store for AR Memorabilia